fbpx

Laying roofing sheeting: features and technology

How to properly lay the corrugated board on your roof. A small note for residents in NYC

The profile configuration, as well as its height, can vary greatly. When choosing a corrugated board, it is necessary to consider the peculiarities of the roof, which it is planned to cover. Today it can be purchased at an affordable price from any of a variety of vendors.

By the way, I order services for roofing with profiled sheets in our company “SIGMA BUILDERS,” we give prices for metal profiles below-market prices because we buy corrugated boards directly from manufacturers at a wholesale price. You can find out the corrugated board’s cost by calling +17184509282– we give our clients the lowest prices in NYC. The work on laying the corrugated board always begins with taking measurements of the roof. This will determine the required amount of material.

Roofers “Roofing in NYC” is a free measurement of the roof – the calculation of the cost of work and material for installing a shelter from a profiled sheet.

Be sure to take into account the angle of inclination of each roof slope. If the indicator of this parameter does not exceed 14 degrees, then the sheets are laid by the overlap method with a grip of about 20 cm. If the roof slope is inclined at an angle of 15-30 degrees, then the grip is made 15 cm, and if more than 30 degrees, then 10 cm. As you can see, the greater the angle of inclination of the slope, the less the capture of sheets.

You can always negotiate with your contractor on the price of a successful project before signing a contract. Discuss your budget with your top contractors NYC. Agree that any unexpected project expenses will be presented in writing to help you remain within your budget

The joints between the sheets of corrugated board, if they are laid at an angle of fewer than 12 degrees, are carefully sealed. For this, silicone is usually used.

The type of corrugated board used determines the method of mounting the lathing. For C20 grade material, a solid crate is made, for C35 – with a step of 30-50 cm, and for C44 – with a measure of 50 cm. If you just plan to change the old coating to a new one, the crate does not need to be altered.

Since the profiled sheets are relatively lightweight, they do not exert significant loads on the roof. This eliminates the need to build a robust and, accordingly, expensive rafter system. To fix the corrugated board on the roof, roofing screws are used. The end of such a fastener has a kind of drill, and a neoprene lining is located under its head. The color of the roofing screws can be different, which allows you to choose fasteners for any color of the corrugated board.

Self-tapping screws are twisted only through the descent of the sheet wave. Self-tapping screws 8 cm long are used to fix the ridge of the roof and 4–5 cm for all other sections of the top. To create cuts on the corrugated board, for example, for passages or grooves, metal shears or a circular saw are used. The resulting metal shavings are removed with a soft brush. The grinder cannot be used for cutting corrugated boards.

How to choose a roof  Installation?

Relatively lightweight, inexpensive, and easy to install, asphalt shingles are the best choice for most houses. They come in sheets that are layered on a roof to give the illusion of more expensive single shingles, such as cedar and slate, that are installed one shingle at a time.

The most common residential roofing material used in the United States, asphalt shingles are popular because they are economical and easy to install. These shingles can be reinforced with fiberglass or organic materials (cellulose) without changing the appearance of the shingle.

What to do if there is a scratch on the metal profile (corrugated board) ?

If scratches appear on any sheet, they are immediately painted over with a paint that matches the color. The edges of the sheets from the side of the roof arch are also covered with paint. It is not recommended to use aerosol paints and varnishes for this. Gloves and protective clothing should be used when installing the corrugated board. If the sheets are cut with a circular saw, then you must also wear special glasses.

When laying corrugated board, it is essential to remember that its sheets have a rather slippery surface. Therefore, you should walk on it in shoes with soft soles, additionally insuring yourself with a rope. In this case, you can only step on the descent of the wave of sheets in the places of its contact with the crate. If you neglect this, then you can firmly bend the corrugated board.

Need of Regular Roofing Services - christinarobson.over-blog.com | Residential roofing, Commercial roofing, Roofing services

Your roof estimate should include the number of penetrations and the specific kind of boot that’ll go around them. The estimate should also include any flashing your best roofing company NYC. Flashing is metal placed anywhere the shingles butt up against something, such as a wall, chimney, or in open valleys If snow can slide off the metal roof in winter, snow holders are additionally installed when installing the corrugated board.

Fastening the drainage system to corrugated board

The elements of the drainage system are attached to the crate and not to the sheets of corrugated board. For this, special hooks are used. All other sections of the roof are covered with profiled sheets.

If you decide to change your old roofing to a corrugated board – call us at +17184509282. Our manager will offer you the best price and will measure for free during the day. We work seven days a week, regardless of the season and weather conditions.

We work with many roofing manufacturers and guarantee low prices. We will make the best offer for you in Moscow and give a guarantee for the work performed.

Leave A Reply

Your email address will not be published. Required fields are marked *